100 Fire Doors, Two Identical Defects. Which Door Should You Fix First?
Author
John Tiernan
Date Published

Two fire doors have torn smoke seals. Both close and latch during the inspection. One protects the compartment that nursing home staff rely on when moving residents during a fire. The other is in a day-use area with independently protected escape routes. The maintenance team can attend to one door this morning. The evacuation strategy tells you which one takes priority.
A fire door survey should give the client enough information to decide what needs attention, in what order, and on what evidence. That takes a wider view than the defect in front of the inspector. It means understanding the complete doorset, the people who depend on it and the other fire precautions that have to work alongside it.
What Does the Door Need to Do?
Start with the fire risk assessment, fire strategy, evacuation procedures and available compartmentation and escape drawings. Walk the building with someone who knows how it operates. Establish what the door is required to do, who depends on it, and where those people could go if the route or compartment became unusable. Check whether any alternative escape route is genuinely independent and usable by the people expected to take it. In a care setting, consider assisted evacuation and the staffing available at night.
Assess the leaf, frame, glazing, seals, hardware and visible frame-to-wall details together. Record what was observed, measured and functionally checked, and identify the evidence that applies to that assembly. A door that closes correctly may still have a damaged seal or an unsupported alteration. Where a clearance is in question, compare the measured gap with the applicable assembly evidence and check any required smoke-control performance. If the role of the door is unclear, record the highest credible consequence provisionally and assign someone to verify it.
Review defects collectively where several doors protect the same stair, corridor or compartment. A door-by-door review can miss the effect of several impairments on the same evacuation route. Feed significant findings back into the fire risk assessment and works programme. BS 8214:2026, clause 15.1, pp. 38-39, recommends risk-based inspection and integration of maintenance with the building's fire risk management plan.
How Are Condition and Consequence Graded?
D Grades Describe the Condition of the Installed Assembly
Grade | What it means and what it can look like |
|---|---|
D1 Minor | No identified effect on required function. Examples include superficial scuffs with the leaf surface intact, or faded identification where the assembly remains traceable. |
D2 Limited concern | A local defect or evidence gap with reasonable confidence in continued function. Examples include a seal lifting locally while effective contact is maintained, or missing installation instructions where the door is identifiable and other records support the required performance. |
D3 Material impairment | A significant defect or substantial doubt about required performance. Examples include a torn smoke seal leaving an open section on a smoke-control door, or distortion producing gaps materially beyond the assembly's documented limits. |
D4 Failed function | A required function is unavailable. Examples include a self-closing door remaining open when released, a required latch failing to engage, or missing glazing that leaves an open aperture. |
C Grades Describe the Consequence if the Door Fails During a Fire
Grade | What it means and what it can look like |
|---|---|
C1 Low | Limited foreseeable life-safety consequences. For example, a local separation between low-occupancy areas with little exposure and no material effect on escape. Record the basis for this judgement. |
C2 Moderate | Potential local spread, with verified independent escape and limited reliance on the door. For example, a separation in a day-use area with independently protected escape routes. |
C3 High | Potential significant exposure of a primary escape route, sleeping occupants or another occupied area. For example, a higher fire-risk room opening onto a primary protected corridor where an independent escape route is available. |
C4 Critical | Failure could compromise the only viable escape route or a boundary essential to assisted evacuation. Examples include a door protecting the only viable stair or a compartment door protecting a receiving area essential to progressive horizontal evacuation. |
How Does the Matrix Set the Priority?
Find the condition grade on the left and the consequence grade across the top. The intersection gives the starting priority. Review it against site conditions and the combined impact of other defects.
Condition | C1 Low | C2 Moderate | C3 High | C4 Critical |
|---|---|---|---|---|
D4 Failed | P2 | P1 | P1 | P1 |
D3 Material | P3 | P2 | P2 | P1 |
D2 Limited | P4 | P3 | P3 | P2 |
D1 Minor | P4 | P4 | P4 | P4 |
Phoenix STS Editorial Note. Notify management immediately when a required fire door function has failed. BS 8214:2026, clause 15.1, recommends immediate inspection and remedial action for major failures in door function. Verify any interim controls before relying on the affected door, route or compartment. Restrict affected use if safety cannot be demonstrated. Use the matrix periods to plan permanent work and take any immediate safety action required at discovery.
- P1 Immediate. Notify site management immediately and restore function where practicable. Otherwise, verify interim controls before continuing to rely on the affected route or compartment. Restrict affected use if safe operation cannot be demonstrated. Set a completion date and review controls at least daily while the impairment remains.
- P2 Urgent. Notify management that day, assign an owner, assess interim controls and target completion within seven calendar days.
- P3 Prompt. Assign an owner and target completion within 30 calendar days.
- P4 Planned. Schedule the work within 90 calendar days.
Escalate immediately where required escape is blocked, the leaf or glazing presents an immediate injury risk, or combined defects defeat the evacuation strategy. Major functional failures call for immediate inspection and remedial action under BS 8214:2026, clause 15.1, p. 38. A matrix target for completing permanent work leaves that immediate response in place.
The D, C and P grades and the 7-, 30- and 90-day periods are proposed management tools for this matrix. Targets run from discovery. Apply any shorter binding deadline and escalate if conditions deteriorate or interim controls become ineffective.
How Does This Work in Practice?
These illustrative scenarios show how the same defect can lead to different priorities and how each finding can be taken through to close-out.
Nursing Home with Two Damaged Smoke Seals
Both doors close and latch, but the tears create substantial doubt about the required smoke-control function, so both are D3. Door A protects a compartment used for progressive horizontal evacuation. Staff may need to move residents through it into an adjoining compartment as an initial place of relative safety. It is C4, giving P1. Door B serves a day-use area where independent escape has been verified and reliance on the door is limited. It is C2, giving P2.
The inspector informs the person in charge immediately. In this example, a compatible seal must be sourced for Door A. Management and the fire safety assessor review the affected evacuation arrangements and temporarily move the residents who depend on that boundary to a suitable area after checking staffing, capacity and escape arrangements. The person in charge records and reviews the arrangements daily. Door B receives a dated work order.
The contractor identifies the assemblies and installs seals supported by the manufacturer's specifications. A competent person checks the installed seals and verifies closing and latching as required. The door register records the component evidence and checks. Management reinstates the original arrangements after Door A is verified, and Door B is completed within its seven-day target. For seal replacement, see BS 8214:2026, clause 15.2.3, p. 40. For fire precautions in designated centres for older people, see regulation 28(1)(c)(i) and 28(2).
Commercial Premises with Two Distorted Steel Fire Doors
Both doors still close, but both have gaps beyond the identified assembly evidence and are graded D3. Door C separates a workshop from the building's only viable protected stair. It is C4, giving P1. Door D separates low-occupancy areas whose occupants have independently protected exits. The assessor records the limited foreseeable life-safety consequence and grades it C1, giving P3.
Management restricts use of the area that depends on the stair until protection is restored. The manufacturer confirms that Door C has no supported repair or compatible replacement leaf, so a complete assembly is specified against the required performance and supporting construction. For Door D, the manufacturer can supply a replacement leaf with evidence covering compatibility with the retained frame, hardware and applicable seals. The contractor installs Door C first. A competent person checks the installation against its supporting evidence and verifies required self-closing and escape operation before management reopens the area. Door D is installed and verified within its 30-day target. BS 8214:2026, clause 15.2.1, p. 39, addresses repair, replacement and compatibility with retained components.
How Does a Survey Become a Workable Programme?
- Agree the order of work with site management. Record each door's ID, location, required function, condition and consequence grades, reasons, evidence, owner and target date. Agree immediate controls and their review frequency before leaving critical findings open.
- Define the next action for each door. Specify a supported repair, raise a targeted investigation where the evidence is incomplete, or specify a compatible component or complete replacement where needed. Give each investigation a specific question and a due date.
- Match the work to the resources available. Assign in-house work within the team's competence and order specialist work or long-lead replacements early. Group lower-priority jobs by zone or component where deadlines allow. Check the effect of taking doors out of service during the work. If a target slips, retain the original date and record the revised date, reasons and interim controls.
- Verify and close out. Set acceptance checks when raising the job. Record what was fitted, what was measured or tested, who verified it and where the evidence is held. Update the door register and, where the building's fire precautions are affected, the fire risk assessment.
In Ireland, section 18(2) of the Fire Services Act 1981, as substituted by section 29(b) of the Licensing of Indoor Events Act 2003, sets out the duties of persons having control of applicable premises. Those duties include providing reasonable fire safety measures and appropriate procedures and ensuring they are applied. A phased works programme documents how the premises is dealing with findings and managing unresolved impairments.
For every open item, the client should be able to answer three questions. Why is this door being dealt with at this priority? What evidence supports the work? How are occupants protected until the door's required function is verified?
Technical and Statutory References
- Fire Services Act 1981, section 18(2), as substituted by section 29(b) of the Licensing of Indoor Events Act 2003
- S.I. No. 415/2013, regulation 28, Fire precautions
- HIQA Fire Safety Handbook for designated centres
- BS 8214:2026, BSI publication record. British technical guidance on the specification, design and performance in use of fire-resisting and smoke control doors.
Phoenix STS provides a Fire Door Inspection Course and a Fire Door and Passive Fire Protection Inspection Course.
Subscribe to the Phoenix STS newsletter for fire safety and health and safety updates.
Important Note
This article is for general information. Management should use a competent person's site-specific assessment, the applicable requirements and the installed assembly evidence to decide on immediate precautions, repairs and reinstatement. The illustrated timescales are internal planning targets. Apply any shorter binding deadline and act sooner where the risk requires it.

A fire door sign does not prove fire resistance. John Tiernan explains how inspections, FSC records and the current building determine what each door must do.

Learn how to coordinate fire risk assessment and fire door inspection findings in Ireland to set clear priorities, define remedial work and improve safety.
